Rabbitfilms X Chimera7 Pro 6S FPV Long Range Analog - BNF

Rabbitfilms X Chimera7 Pro 6S FPV Long Range Analog - BNF

$469.99
Product Code: L012695
Stock In Stock

Available Options

Product Description


Introducing what has been requested for too long already! A super efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above. 


GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts are included to cover you and your antenna dead-ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).


Tips:

VTX is set to 25mW by default! Power levels above 25mW require a HAM license or have to be approved by local authorities! Please ensure you're flying legal frequencies and use our prepared Betaflight VTX tables according to your region.




HIGHLIGHTS:

- Battery voltage LED status light (illuminated Rabbit logo on the bottom)

- GoPro TPU bottom stand (GoPro protector not included)
Lightweight Side Panels Design - Keep Your Rig Clean
- XING2 2809 1250KV efficient wide stator motors

- GPS pre-installed for more safety at a distance

- 360° TPU protection, FPV cam protection

- 6mm rigid arm design for more stiffness

- Top- and bottom battery mount option

Brand new color of TPU print parts

- Rabbit logo on the top plate


PRE-TUNED & PRE-SETUP:

- Is this your first BNF or are you just starting through with FPV? This article might probably help: General Guide // iFlight BNF

- Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

- Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"

- GPS Rescue is OFF by default to prevent unwanted or unexpected drone behavior.

Please check our linked article on "GPS Rescue Mode // Setup"


Specifications:

- Weight: 695g (without battery and GoPro mount)

- Total Dimensions: 258*200mm (body dimension)

- Upper(middle) Plate Thickness: 3mm

- Bottom to Top Distance: 20-29mm

- ESC: BLITZ E55 4-IN-1 2-6S ESC

- Bottom Plate Thickness: 3mm

- Camera Plate Thickness: 3mm

- Top Plate Thickness: 3mm

- Geometry:  DC (DeadCat) 

- HQ 7.5X3.7X3 Propellers

- Arm Thickness: 6mm

XING2 2809 1250KV

- Wheelbase: 321mm

- FC: BLITZ F722


ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)


FC // BLITZ F722 Flight Controller

  • Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
  • Smartaudio / IRC Tramp VTX protocol supported
  • Firmware target: IFLIGHT_BLITZ_F722
  • Motor outputs: 4x (SH1.0 connector)
  • Flash: 32MB (Blackbox flash)
  • I2C serial: SDA / SLA pads
  • Dimensions: 36.5*35 mm
  • Barometer: DPS310
  • OSD Chip: AT7456E
  • LED controller: Yes
  • MCU: STM32 F722
  • Beeper pad: Yes
  • Gyro: BMI270
  • Weight: 7.8g
  • UARTS: 6

 Product Link


ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

  • Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
  • Mounting Holes: 30.5*30.5mm/Φ4mm
  • Target:   IFLIGHT_BLITZ_G2
  • Supports 2-6S Lipo input
  • Current sensor: Yes
  • Constant: 55 Amps 
  • Current rate: 200
  • Burst: 65 Amps
  • Weight: 15.3g
  • MCU: G071
  • BEC: No

 Product Link


VTX// BLITZ 1.6W VTX Adjustable
  • Betaflight IRC Tramp Configuration: Please download the attached VTX table for Betaflight!
  • IRC Tramp VTX table values: 25mW/400mW/800mW/1600mW
  • Power levels: PIT/25mW/400mW/800mW/1600mW
  • All our VTX tables can also be found here: LINK
  • Lightweight: 18.9g (excluding antenna)
  • Mounting pattern: 30.5x30.5mm/Φ3 
  • Channels: 40 (including Raceband)
  • VTX telemetry: IRC Tramp
  • Input voltage: 7V~36V 
  • Interface: MMCX


Chimera7 Pro Analog BNF Included Components and Parts

  • 4 x HQ 7.5X3.7X3 CW propeller + 4 x  HQ 7.5X3.7X3 CCW (Color may vary)
  • 1 x RaceCam R1 Mini 1200TVL 2.1mm 19*19 camera
  • 1 x Albatross RHCP 5.8GHz SMA FPV Antenna
  • 2 x iFlight Lipo Strap 20*250mm (Black)
  • 1 x Pre-built and Tested Chimera7 Pro


Tips:

VTX is set to 25mW by default! Power levels above 25mW require a HAM license or have to be approved by local authorities! Please ensure you're flying legal frequencies and use our prepared Betaflight VTX tables according to your region.

Write a review

Please login or register to review
$1 IFPV Points IFPV Points