Nazgul5 HD w/Caddx Polar Vista Digital HD System BNF + DJI Goggles V2

Nazgul5 HD w/Caddx Polar Vista Digital HD System BNF + DJI Goggles V2

$942.99
Product Code: F011014
Availability: In Stock

Available Options

Product Description


Nazgul5 HD is a 5" size BNF (Bind-and-Fly) quadcopter with Caddx Vista Digital HD System on it. We sticked the lighter Caddx Vista on one of our new updated XL5 V5 FPV frames. Pre-tuned and setup, everything you need is just bind-and-fly! Loads of power and smooth flights guaranteed using our popular XING-E motors with long-lasting NSK bearings. Got a hard hit and snapped an arm? Don't worry, get some spares with your order and easy-swap out in field. Wanna strap your GoPro on that beast as well? Checkout our collection of high quality TPU prints for your cam!


HIGHLIGHTS:

- 5mm arm design for more durability

- Easy-Swap arms

LED illuminated Logo

- XING-E 2207 motors and NAZGUL 5140 props
- 5" version also fits 5.1" style propellers
- Popular True-X configuration
- TPU crash-guards
- Fits both 30.5x and 20x stacks


Nazgul5(XL5 V5) frame specs:


PRE-TUNED & PRE-SETUP:

- Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

- Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"


BNF // Parts lists

  • 1x Prebuilt and tested Quadcopter
  • 1x DJI HD FPV Goggles V2
  • 1x Nazgul5(XL5 V5) Frame
  • 1x Caddx Polar Vista Digital HD System Kit
  • 1x Albatross LHCP RP-SMA 5.8g antenna
  • 2sets x Nazgul 5 inch 3-blades (Set of 4 - Color may vary)
  • 1x 20*200mm Microfiber PU Leather Battery Strap (Color May Vary)
  • 1x 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)


FC // SucceX-E F7 Flight controller

- MCU: STM32F722 216MHz

- Gyro: MPU6000

- Baro: NO

- OSD: IFLIGHT OSD AT7456E

- BEC: 5V 2.5A

- BlackBox: 8MB

Currentscale: 100(WithiFlightESC)

- Uart: 4*UART(UART1UART2UART4UART5)

- UART1 for VTX HD/Analog Telemetry

- UART2 for Receiver

- UART4 for GPS 

- UART5 for ESC Telemetry

- 4×Dshot/PWM outputs

- Smartaudio & IRC Tramp VTX protocol supported

- WS2812 led Strip: Yes

- Bepper: Yes

- Firmware: IFLIGHT_SUCCEX_E_F7 4.2.0

Outer Size: 36*36mm / 30.5*30.5/φ4 mounting

- Weight: 6.9g


ESC // SucceX-E 45A 2-6S BLHeli_S 4-in-1 ESC

- Dimension: 40*43mm

- Mounting Holes: 30.5*30.5mm/Φ3mm

- Weight: 14.4g

- Supports 2-6S Lipo input

- STM32F051 MCU, 48Mhz Runs BLHELI 16.X Firmware

- Current sensor: YES

- BEC: NO

- Supports: DShot150/300/600/1200/MultiShot/OneShot etc.

- Target: G-H-30 BLS 16.7


Changelog:

June 2021: Upgraded SucceX-E F4 flight control to SucceX-E F7


Additional Suggested Parts


Important

The DJI Remote Controller is recommended for beginners since you won't need to set up another receiver, but it is also optional in this BNF drone because it is NOT required in order to use the FPV system. If you don't choose to use the DJI Remote Controller, you can choose a receiver option for your transmitter. and then bind to your own radio as usual.

  • Our current frsky receivers default version in 2.XX, requires to use the same version of frsky transmitter. 
  • If you have none frsky transmitter,please downgrade the version lower than 2.X.X, www.frsky-rc.com for more details.


Note:

All iFlight BNFs are tested before shipment to guarantee highest quality. 

If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.

iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support

Write a review

Please login or register to review
-9%
$1 IFPV Points IFPV Points