AOS 5 V2 HD 6S w/Nebula Pro Vista HD System - BNF

AOS 5 V2 HD 6S w/Nebula Pro Vista HD System - BNF

$495.00
Product Code: F013027
Stock Pre-Order

Available Options

Product Description




Exceptional flight performance. Lightweight. Ultra-low vibration. Easy to maintain. This is state-of-the-art FPV V2.0.

When I set out to create a bind and fly version of the AOS 5 V2 I had a vision to combine the latest and greatest technology into the ultimate FPV freestyle machine. This is the result. - Chris Rosser, AOS RC

Frame: The AOS 5 V2 has been designed to deliver the ultimate freestyle flight experience. The unique arm geometry has been refined through topology optimization to deliver maximum strength and stiffness for minimum weight. The same technology is used to optimize aircraft, satellites and race cars.

Motors: Exhilarating speed, silky smooth flight after flight. iFlight's XING2 2207 motors provide power and durability with a 7075 Aluminium unibell design, 5mm titanium shaft, Japanese NSK bearings, N52H center slotted arc magnets, and an integrated o-ring for bearing protection.

Electronics: Blazing fast with less filter delay for a more locked-in flight feel. The F7 flight controller takes maximum advantage of the vibration performance of the frame with a custom filter tune to reduce latency and improve propwash handling. With OSR4 mode enabled in BF4.3 the BMI270 gyro delivers latency and noise performance that matches or exceeds that of the MPU6000. A BLHeli32 ESC smoothly delivers power to the motors and the massive 55A rating ensures the motors will have all the power they could ever need.

Key features:

  • 32x32mm GoPro mounting holes in top plate with installed press-nuts
  • Designed for up to 5.1 inch props, no props in view
  • Recommended 1000-1300mAh 6S battery
  • ~350g without battery
  • Captive battery straps
  • 220mm wheelbase
  • 6 mm Arms


ELECTRONICS // BLITZ Mini F7 Stack (F7 V1.1 + 55A 4in1 ESC)


FC // BLITZ MINI F7 V1.1 (SKU: BF12000)

  • Mount pattern:   20x20 mm / 4mm PCB hole diameter, silicon grommets for M3 screws
  • Smartaudio / IRC Tramp VTX protocol supported
  • Firmware target:   IFRC-IFLIGHT_BLITZ_F722
  • Motor outputs:   4x (SH1.0 connector)
  • Flash:  16MB (Blackbox flash)
  • I2C serial:   SDA / SLA pads
  • Dimensions:   30.5x27 mm
  • MCU:   STM32 F722
  • Barometer:  DPS310
  • OSD Chip:   AT7456
  • LED controller:   Yes
  • Beeper pad:   Yes
  • Gyro:   BMI270
  • Weight:   5g
  • UARTS:   6


ESC // BLITZ Mini 55A  (SKU:BE11376)

  • Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
  • Mounting Holes: 20*20mm/Φ4mm
  • Target:   IFLIGHT_BLITZ_G2
  • Supports 2-6S lipo input
  • Dimension: 35*42mm
  • Current sensor: Yes
  • Firmware: BLHeli 32
  • Constant: 55 Amps 
  • Current rate: 100
  • BlackBox: 16MB
  • Burst: 60 Amps
  • Weight: 11.3g
  • MCU:G071
  • BEC: NO

 Product Link



AOS 5 V2 HD Included Components and Parts

  • 4 x Nazgul F5 - CW propeller + 4 x Nazgul F5 CCW (Grey)
  • 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 75mm
  • 1 x Pre-built and Tested AOS 5 V2 HD BNF
  • 1 x iFlight Lipo Strap 20*250mm (Black)
  • 1 x iFlight Lipo Strap 15*250mm (Black)
  • 1 x Nebula Pro Vista HD System



Note:

All iFlight BNFs are tested before shipment to guarantee the highest quality. 

If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.

iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support




Write a review

Please login or register to review
-12%
-9%
-10%
-8%
-10%
$1 IFPV Points IFPV Points